slogan

Тестирование груза

Продукция » Такелажное оборудование » Тестирование груза

1500 TM LOAD TESTING MACHINE

1,500 ton capacity hydraulic traction-type testing machine to give safety-critical lifting components such as hooks periodic “health” checks in the form of load tests. The machine can accommodate components up to 6,000 x 2,000 x 2,000 mm. The machine itself measures 10,500 x 4,500 x 3,350 mm and weighs 94,500 kg.

Hooks, hook blocks and other safety-critical components can be tested theoretically and physically. In more detail this can be theoretically via calculation on paper, or by computer with finite element modelling and analysis, or by physically testing a component ‘in the metal’.

When cranes are destined for applications where there is a risk of endangering human life, the safety factor (SF) must also be determined, in addition to the tests required by DIN/BS/ASTM, etc. The safety factor is calculated as the tensile strength (TS) divided by the safe working load (SWL).

Preparing a hook for testing in the new 1.500 tonne capacity machine at Forjas Irizar.

When cranes are destined for applications where there is a risk of endangering human life, the safety factor (SF) must also be determined, in addition to the tests required by DIN/BS/ASTM, etc. The safety factor is calculated as the tensile strength (TS) divided by the safe working load (SWL).

According to these standards (DIN/BS/ASTM), tensile strength is marked 1:4.5 and the minimum yield stress marked by standards is 1:2.7: that means, that at 2.7 times the allowed load, the most important component in the hook block – the hook – would begin to deform and then could break at 4.5 times the maximum allowed load.

Other values can be obtained by applying finite element modelling standards to determine the fatigue strength of the critical parts of a component such as a hook block but they are still theoretical calculations. To be reliable, physical overload tests must be carried out: that is, to subject the component to traction under a controlled load higher than the safe working load. For such calculation there are formulas but the one that Forjas Irizar applies is according to its own PC10.4 procedure:

  • For components with a maximum permitted load up to 25 tonnes, the PTL = SWL x 2
  • For components with a maximum permitted load above 25 tonnes, the PTL = (1.22 x SWL) + 20 tonnes

For example, when a component is designed for a maximum permitted load of 15 tonnes, the load test must be carried out at 30 tonnes: 15 tonnes x 2. When a component is designed for a maximum permitted load of 150 tonnes, the load test must be carried out at 203 tonnes: (150 tonnes x 1.22) + 20 tonnes.

In this way, in the worst case scenario, components tested to twice the SWL never reach their yield stress since the minimum safety factor is 1:2.7.

Test of a hook for use in the nuclear industry.

In addition to DIN/BS/ASTM standards, Forjas Irizar recommends considering the influence of other important technical characteristics that must be taken into account, especially in heavy duty applications, such as steel works.

Once the hook is in use, it should get special attention regarding its material properties in relation to the effects of corrosion, fatigue, erosion and wear.

Fatigue is the subject of this article, since corrosion and erosion are covered in International Standards and corrosion from the action of seawater would be the subject of a separate article.

Fatigue

How should fatigue, which can be described as the cholesterol of lifting parts, be checked? Fatigue is the number one factor to have under control. It reveals itself when materials are submitted to repetitive traction cycles and it can cause catastrophic failure in a component such as a lifting hook.

Fatigue that can cause a hook to break presents itself in two well-defined areas; one is on the outside in the form of crack initiation and first succession. The second is internal, by a sudden break in a weak section.

Causes of breakage by fatigue can be, for example, accumulated energy in the material as a consequence of the elastic hysteresis to which it is exposed during each lifting and lowering cycle.

The fatigue process happens in four phases:

Phase A During the hook’s first lifting and lowering cycles (about 5% of the total) some fibre-band orientations start internally, in the grain of the steel. At the same time, on the outside surface of the piece, crests and valleys (extrusions and intrusions) appear.

Phase B After more cycles (about 25% of the total) the first inter-band cracks appear inside in the grain of the steel. At the same time, surface intrusion and extrusion becomes more and deeper.

Phase C As the number of cycles advances (up to 75 % of the total), superficial extrusions grow, becoming cracks that deepen inside at the same time that inter-band cracks increase in quantity and magnitude.

Phase D During the final cycles, as a consequence of not taking preventive action in the earlier phases, the component breaks in the area that has been weakened by fatigue.

What influences fatigue?

  1. The form and amplitude of stresses (where compression and tension forces are unequal)
  2. The temperature of the component
  3. Oscillation frequency
  4. Surface condition of the object
  5. The grain size of the metal.

A crucial consideration is the “incision effect”. This effect is produced as a result of the geometrical form (or other reasons) causing stress concentration areas or points in the component. Examples include surface damage in the form of notches, and design or manufacturing flaws, where there are sharp corners without a large enough or smooth radius of material.

Manufacturer’s recommendation

Where there is any doubt about the status of lifting components they should be checked. This kind of preventive action saves lives. In light of the serious consequences of negligence in checking or inspecting hooks during Phases B and C, above, Forjas Irizar recommends that periodic overload tests under controlled conditions are carried out.

There are some standards, norms and regulations where it is indicated that overload tests should be done at least once a year, or earlier, depending on the number of cycles. In addition, it is recommended that the overload test is applied not only to the main component (the hook) but also to all the parts that constitute the complete hook-block; hook, nut, crosshead, shafts, bearing, sheaves, ropes, etc. Any parts that fail under a controlled overload test in a test rig while the component is off the crane have minimal consequences compared with the potential disaster of their failure when in use on a crane with a load suspended on the hook.

Версия для печати PDF

Скачать в формате PDF

Для просмотра файлов Вам понадобится программа чтения файлов в формате PDF



Если она у Вас не установлена — можете скачать и установить:

PDF Reader Оригинальная программа от компании Adobe — Adobe Reader (Acrobat Reader) (~ 24 Мб)



PDF Reader Альтернативная прогрограмма — Foxit Reader (Её преимущество — меньший обьем и большая скорость работы ) (~ 4 Мб)

spp
ООО "Флуитек Системз" является членом УСПП


+38 (0542) 677-271
+38 (0542) 677-272
+38 (050) 308-92-92

Одно из направлений нашей работы - силовые гидравлика и пневматика. Будучи партнером группы европейских фирм-производителей, мы предлагаем к поставке материалы и комплектующие для гидро- и пневмосистем высокого и низкого давления, работающих с любыми средами.

Мы находимся по аресу:

Украина, г. Сумы, ул. Черепина, 60, офис 3


Карту проезда и дополнительную информацию, вы всегда можете посмотреть в разделе Контакты

Всеми правами на сайт и размещенную на нем информацию обладает компания Флуитек Системс а также компании, которые она представляет © 2009-2011 Copyright Fluitech Systems®


Разработка, поддержка, раскрутка — Флуитек Системз